Q600-SLIM direct flow reverse osmosis 95lt./h. with 2-way faucet, with TDS regulator

The Q600-SLIM system is a compact, professional reverse osmosis unit designed to ensure a consistent production of 1,6 ltr./min. of high-quality water.
With a thickness of only 9,8 cm it makes the system perfect for toe-kick installation, even in the most modern kitchens where available space is very limited.
Featuring an innovative multi-stage configuration, along with a next-generation filter and membrane replacement system, the Q600-SLIM guarantees quick and easy maintenance.
Thanks to the two separate outlets located on the rear of the device, the Q600-SLIM allows you to instantly dispense two different types of water: reverse osmosis water and filtered water.

Filtration
The system uses a 5-stage purification process engineered to deliver complete water treatment:

Stages 1-2: PP + Carbon Block Filters
Remove sediment, sand, rust, suspended impurities, and solid particles, protecting the RO membrane and improving the overall efficiency of the system.

Stages 3-4: RO Membranes
The two high-precision 300GPD membranes, with a filtration level of 0,0001µm, significantly reduces undesirable substances such as dissolved salts, heavy metals, contaminants, bacteria, and viruses, while allowing only pure water molecules to pass through.

Stage 5: Alkaline Filter
Restores the water’s pH to slightly alkaline values (around 7,5), reintegrating beneficial minerals and improving taste and user experience.

As an alternative at Stage 5, an Activated Coconut Post Carbon Filter (to be purchased separately) can be installed, designed to remove unwanted odors and improve the taste of the water.

Main functions and components:
- High-efficiency booster pump to ensure stable flow.
- Integrated UV sterilization with dedicated indicator and end-of-life alert.
- Automatic autoflushing at start-up, after 24 hours of inactivity, or after prolonged production cycles, to protect the membrane.
- TDS adjustment: the value is displayed in real time on the front display, and the dedicated dial on the rear panel allows the user to set the desired outlet TDS.
- External leak-protection system: if a water leak is detected, the device stops and reports the issue on the display.
- Overload protection: the system automatically stops after 30 minutes of continuous filtration.

Smart display with orientation sensor (vertical/horizontal) showing:
- Remaining filter life
- Pre-membrane pressure
- UV system status
- Operating modes and alarms

Maintenance
Filters and RO membrane replacement is performed through a quick click-in system.
The display automatically notifies when components are exhausted and guides the user through the reset procedure.

Technical specifications:
- Rated voltage/frequency: 100–240V. - 50/60 Hz
- Rated power: 70W.
- Inlet water pressure: 0,1-0,4 MPa (1-4 bar)
- Outlet water flow rate: 1,59 ltr./min.
- Operating temperature: 4-40 °C
- Dimensions: 460×98×420 mm.

Components included in the package:
1× Instruction manual
1× 2-ways faucet
1× Ballast
1× Teflon roll
1× External anti-flood sensor
1× Installation kit with tubing, quick-connect fittings, clips.

The reverse osmosis is not a device that makes water drinkable(non-drinkable water into drinkable water) and it work only if it's installed on water compliant with the law, municipal potable water or well water if previously made drinkable with adequate and effective systems, preventively studied and personalized for that kind of water.
Do not use the system where the water is microbiologically dangerous or of unknown quality without adequate disinfection before and after the system. All systems must be preserved according to the producer instructions.
The pollutant parts removed or reduced by this system are not necessarily in your water.
In case of potable inlet water of bad quality, it's possible to close all the outgoing mineral salts regulator (TDS) and to mount, as the last stage, a remineralizer filter that stabilizes the Ph.
1x Ionicore remineralizer PH adjustment coconut in line filter (GAC) 1/4" FPT 2"x10".