The RO UX800 is a latest generation RO system able to provide up to 2 liters per minute of osmotic water thanks to its 800 GPD membrane, and up to 8 liters per minute of filtered water.

In fact, with the RO UX800 system, users can choose whether to dispense hot/cold water directly from the mains supply (bypassing the system), or filter it through the dedicated sediment+carbon filter that removes particulates, odors, and tastes.

Filtration Stages
Filter 1: Sediment + Carbon Block
Filter 2: RO Membrane 800 GPD
Filter 3: Carbon Block

Specifications cod. 050055-010 - Sediment + CTO carbon block filter
- Service flow rate: 8 l./Min. (2,11 gpm)
- Temperature: 39 - 100°F (4-38°C)
- Pressure: 14 - 58 psi (1 - 4 bar)
- Filtering density: 5 micron

Specifications cod. 050055-011 - RO membrane 800GPD
- Service flow rate: 2 l./Min. (0,53 gpm)
- Temperature: 39 - 100°F (4-38°C)
- Pressure: 14 - 58 psi (1 - 4 bar)
- Filtering density: 0.0001 micron

Specifications cod. 050055-012 - CTO carbon block filter
- Service flow rate: 3 l./Min. (0,8 gpm)
- Temperature: 39 - 100°F (4-38°C)
- Pressure: 14 - 58 psi (1 - 4 bar)
- Filtering density: 5 micron

- Activation: it is advisable to run water through filter at maximum pressure and full flow rate, for at least 5 minutes to allow air purging and flushing of cartridge.
- Cartridges change: When capacity is reached, or when flow comes too slow (precipitates under 0.7bar/10psi), every 6 months but at least annually.

Filters Replacement
- Turn off the system and close the inlet water supply.
- Open the top cover of the unit.
- Rotate the filter counterclockwise until it detaches, then remove it.
- Insert the new filter into place and rotate it clockwise until you hear a "click" securing it.
- Press and hold the reset button for 3 seconds to reset the new filter's lifespan.

Features:
- Voltage/rated frequency: 200-240V AC - 50/60 Hz - 1.5A
- Rated power: 100W
- Inlet pressure: 0.1-0.4 MPa (1-4 bar)
- Osmotic water flow rate: 2 L/min
- Filtered water flow rate: 8 L/min
- Working temperature: 5-38°C
- Dimensions (mm.): 170x455x455

Accessories included in the packaging:
1x Instruction Manual
1x 1-way stainless steel faucet
1x Faucet assembly kit
2x Flexible hoses
1x Transformer
1x Installation kit

After the reverse osmosis process, it is recommended to install the Ionicore inline filter as final stage. This filter naturally reintroduces calcium and magnesium and, thanks to the coconut-based granular activated carbon (GAC) and its pH regulation function, it stabilizes the water, making it more balanced and pleasant to drink.
1x 07004004 Ionicore remineralizer PH adjustment coconut in line filter (GAC) 1/4" FPT 2"x10"

The reverse osmosis is not a device that makes water drinkable(non-drinkable water into drinkable water) and it work only if it's installed on water compliant with the law, municipal potable water or well water if previously made drinkable with adequate and effective systems, preventively studied and personalized for that kind of water.
Do not use the system where the water is microbiologically dangerous or of unknown quality without adequate disinfection before and after the system. All systems must be preserved according to the producer instructions.
The pollutant parts removed or reduced by this system are not necessarily in your water.