This site uses cookies to improve user experience ok, don't show again read privacy policy x
Languages
Products

DMfit quick fit fittings white series acetal resin inch size food&drink beverage compressed air flow systems

water softeners chlorine producer

produttore-di-cloro_2.jpgHome
 » 
Addolcitori acqua
 » 
Softener accessories
order
other filters

Yellow drain tube for water softener 1/2"
Yellow drain tube for water softener 1/2"
000092
Sold by the meter Features • Ø 12,5 mm (1/2") • Flexible • Anti alga • Operating temperatures from -10°C to 40°C • Pressure 8 Bar 8 years warranty
Yellow drain tube for water softener 3/4"
Yellow drain tube for water softener 3/4"
000093
Sold by the meter Features • Ø 19 mm (3/4") • Flexible • Anti alga • Operating temperatures from -10°C to 40°C • Pressure 8 Bar • 8 years warranty
Chlo Active CL2 complete chlorine maker with Titanium electrode, o-ring, Starfit fittings 3/8"
Chlo Active CL2 complete chlorine maker with Titanium electrode, o-ring, Starfit fittings 3/8"
15000407
OPERATION: Connect the probe on your softener brine line (use the necessary adapters). Check how many liters of resin are there in your softener (look on softener manual). Make sure that the plug of Our generator is disconnected. On the generator's board there is a trimmer that can be setted from 1 to 70 minutes of timer. Every minutes that you program can disinfect 1 lt of resin. The system is ready to start. How it works: The softener during regeneration aspires the brine, our system feels the passage
Chlo Active CL2 - components chlorine maker
Chlo Active CL2 - components chlorine maker
15000402
Replacement parts chlo active Articles to assemble: J173-CPR16IS JG replacement O-ring OD tube 1/2" (x3pcs.) + S001-4200 Straight adaptor OD Tube - M. thread 3/8" x 3/8" (x2pcs.)
Complete chlorine maker with Titanium electrode, o-ring, fittings 3/8" for code 15000124
Complete chlorine maker with Titanium electrode, o-ring, fittings 3/8" for code 15000124
15000435
Specifications Power: 200mA Connection: QC 3/8" tube Total Chlorine Generation: 1.8ppm @ 2.0L/M Saturated Brine draw rate. Salt Alarming: Detect the salt volume in the brine tank simultaneously, alarm if salt is lack(85HE PCB only current). Principal of Work The generator can be installed into the normal Brine Line to produce chlorine through electrolytic reaction during the Brine. Draw cycle, thus killing the bacteria or other relevant microbes that affect the water quality in the co
STERIL-SOFT PRO complete chlorine maker IN/OUT 3/8"
STERIL-SOFT PRO complete chlorine maker IN/OUT 3/8"
15000415
Automatic disinfection system for water softener from 0 to 350 lt. resin. An automatic chloration of ion exchangers in residential water softeners is already required in most European countries. Even if it is not always compulsory, a periodic chloration is often advised in order to avoid bacteriological growth, which can affect softened water characteristics. The automatic disinfection system for softeners Steril-Soft Pro: * Generates chlorine by brine electrolysis during regeneration. * The chlorine
STERIL-SOFT - components chlorine maker
STERIL-SOFT - components chlorine maker
15000416
Automatic disinfection system for water softener from 0 to 90 lt. resin. Titanium electrode not included.
STERIL-SOFT Complete chlorine maker with Titanium electrode, o-ring, Starfit fittings 3/8"
STERIL-SOFT Complete chlorine maker with Titanium electrode, o-ring, Starfit fittings 3/8"
15000418
Automatic disinfection system for water softener from 0 to 90 lt. resin. Important: the time setting must be smaller than the brine draw cycle time otherwise there is a risk of heating and deterioration of the electronic cell. Set-up Instruction: * The adaptability of the Steril-Soft for softeners up to 90 lt. of resin is obtained by setting in the TIME potentiometers inside the box. * The Ampere potentiometer (from 0.2A to 2.5A) regulates the amount of chlorine produced. The bigger t
Quick connector II spacer for BNT valves (25)
Quick connector II spacer for BNT valves (25)
15000436
Dimension (ODxH): 99x63 mm.
Brine valve (3/8")
Brine valve (3/8")
15000439
The brine valve have to be chosen based on the height of the pressure vessel installed in the water softener. In any case, the valves are suitable by adjusting the height to the pressure vessel used. Just follow the instructions below: 15000439-01: Brine valve suitable for all the pressure vessels with height 17" 15000439-02: Brine valve suitable for all the pressure vessels with height 35" 15000439-03: Brine valve suitable for all the pressure vessels with height 44"
37 products found - 2 pages
|< <<
1
2
>> >|

www.sinergroup.it Everpure Filters