Automatic water softener. The BNT650 is a user friendly valve with mechanic regulation. Thanks to its fixed-clicks timer, you will be able to set the regeneration intervals based on the desired timing.
Indicated for commercial and residential usages, the valve can be used both for softening or filtration, with pressure vessels with diameter up to 16"; the valve's body is made of Noryl plastic material.
Complete with ballast 110/240V - 50/60Hz.
The hardness regulation of the outlet water can be adjusted with the mixing valve placed on the side of the valve. Is required output minimum hardness of around 15°F, but the most commonly used setting is not less than 5°F.
To check input/output hardness from the device, we recommend to buy cod. 13000001 Titrant kit total hardness (1°F) 15cc single reagent.

TO BUY WITH EVERY SOFTENER
1x 02001014 3-pieces standard housing 10" clear IN-OUT 1" with wrench & wall mounting bracket.
2x 04001006-05 Ionicore wound polypropylene cartridge 9-3/4" - 50 micron (50)
1x Kit 13000001 Titrant total hardness (1°F) 15cc single reagent.

* Water softeners are supplied without salt, we recommend to use pads salt.
* The pressure tanks are supplied filled up to version "40lit."

The device is supplied programmed with an inlet hardness of 40°F, outlet hardness of 0°F and a safety regeneration every 7 days.

A bypass valve system must be installed on all systems. The bypass valves isolate the device from the water system and allow the use of untreated water. Routine maintenance or service may also require that the system is put in bypass.

Benefits and advantages
Reduction of water hardness, which is cause of scale. ENERGY SAVING: the device prevents the formation of deposits in pipes and hydraulic lines. Greater sense of wellness during the shower. Skin soft and clean. Increased duration of appliances and boilers. COST SAVING: reduction in the use of soaps, fabric softeners and chemicals. Reduced maintenance costs. Fully automatic operation. It should just worry about adding salt in the water softner.

Increased sodium (for drinking water)
Most of the sodium consumed is taken with foods, especially ones obtained with industrial processing. Salt is a great preservative and therefore is used as an additive for processed products. The assumption of sodium with the water we drink is relatively low compared to that which is taken with food. All softeners to produce softened water through ion exchange resins in, produce softened water output sodium ions. The recommended sodium limit for water intended for human consumption is 200ppm liter. Depending on the concentration of sodium and water hardness, it is possible that the water presents a sodium concentration of higher than recommended. Where this is the case or if you need to follow a low salt content, it is advisable to install a reverse osmosis home for water to drink.

Features:
- Flow rate: 4,5 m3/h.
- Connections: IN-OUT 1"M.
- Drain line: quick fitting 1/2".
- Brine line: quick fitting 3/8".
- Regeneration: Down flow.
- Adjustable regeneration cycles in the range 0 - 99 minutes.
- Pressure vessel connection thread: 2,5"NPSM.
- Bottom distributor pipe connection diameter: 1,05"(27mm.).
- Working pressure (min-max): 1,4 - 8,4bar (20,3 - 121,8psi).
- Working water temperature range (°C): 1 - 42.

Model Specifications 15000206-08 8lt. resin (for 1/2 people)
* Exchange capacity: 44ºHFxm3.
* Salt consumption for regeneration: 1.24 Kg. / Salt.
* Water consumption for regeneration: 53,6lt.
* Quantity of water treated for regeneration, 30°F-0,68m3, 35°F-1,26m3, 40°F-1,1m3, 45°F-0,98m3, 50°F-0,88m3, 60°F-0,73m3.
* Max. flow 0.32 m3/h

Model Specifications 15000206-12 12lt. resin (for 2/3 people)
* Exchange capacity: 66ºHFxm3.
* Salt consumption for regeneration: 1,8 Kg./salt.
* Water consumption for regeneration: 80,4lt.
* Quantity of treated water for regeneration, 30°F-2,2m3, 35°F-1,88m3, 40°F-1,65m3, 45°F-1,46m3, 50°F-1,32m3, 60°F-1,1m3.
* Max. flow: 0,54m3/h

Model Specifications 15000206-15 15lt. resin (for 3/4 people)
* Exchange capacity: 90ºHFxm3.
* Salt consumption for regeneration: 2,5 Kg./salt.
* Water consumption for regeneration: 100,5lt.
* Quantity of water treated for regeneration, 30°F-3,00m3, 35°F-2,57m3, 40°F-2,25m3, 45°F-2,00m3, 50°F-1,8m3, 60°F-1,5m3.
* Max. flow 0,68m3/h

Model Specifications 15000206-20 20lt. resin ( for 4/6 People)
* Exchange capacity: 110ºHFxm3.
* Salt consumption for regeneration: 3,2 Kg./salt.
* Water consumption for regeneration: 134lt.
* Quantity of water treated for regeneration, 30°F-3,66m3, 35°F-3,14m3, 40°F-2,75m3, 45°F-2,44m3, 50°F-2,2m3, 60°F-1,83m3.
* Max. flow 0,942m3/h

Model Specifications 15000206-25 25lt. resin (for 6/8 People)
* Exchange capacity: 137ºHFxm3.
* Salt consumption for regeneration: 3,9 Kg./salt.
* Water consumption for regeneration: 167,5lt.
* Quantity of water treated for regeneration, 30°F-4,56m3, 35°F-3,14m3, 40°F-3,91m3, 45°F-3,04m3, 50°F-2,74m3, 60°F-2,28m3.
* Max. flow 0,942m3/h

Model Specifications 15000206-30 30lt. resin (for 6/8/10 People)
* Exchange capacity: 160ºHFxm3.
* Salt consumption for regeneration: 4,3 Kg./salt.
* Water consumption for regeneration: 201lt.
* Quantity of water treated for regeneration, 30°F-5,33m3, 35°F-4,5m3, 40°F-4m3, 45°F-3,55m3, 50°F-3,2m3, 60°F-2,66m3.
* Max. flow 1,47m3/h

Model Specifications 15000206-35 35lt. resin
* Exchange capacity: 175ºHFxm3.
* Salt consumption for regeneration: 5,2 Kg./salt.
* Water consumption for regeneration: 210lt.
* Quantity of water treated for regeneration, 30°F-5,83m3, 35°F-5m3, 40°F-4,37m3, 45°F-3,88m3, 50°F-3,5m3, 60°F-2,91m3.
* Max. flow 1,56m3/h

Model Specifications 15000206-40 40lt. resin
* Exchange capacity: 200ºHFxm3.
* Salt consumption for regeneration: 5,9 Kg./salt.
* Water consumption for regeneration: 240lt.
* Quantity of water treated for regeneration, 30°F-6,66m3, 35°F-5,71m3, 40°F-5m3, 45°F-4,44m3, 50°F-4m3, 60°F-3,33m3.
* Max. flow 1,56m3/h

Model Specifications 15000206-50 50lt. resin
* Exchange capacity: 250ºHFxm3.
* Salt consumption for regeneration: 7,3 Kg./salt.
* Water consumption for regeneration: 262lt.
* Quantity of water treated for regeneration, 30°F-6,66m3, 35°F-5,71m3, 40°F-5m3, 45°F-4,44m3, 50°F-4m3, 60°F-3,33m3.
* Max. flow 1,56m3/h
* The pressure tanks are supplied filled up to version "40lit."