This site uses cookies to improve user experience ok, don't show again read privacy policy x
Languages
Products

telephone
(+39)0773.52.30.14
fax
(+39)06.233.234.260
e-mail
info@sinergroup.it

Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 8-10-12-15-20-25-30 lt. resin

Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 8-10-12-15-20-25-30 lt. resin
printask a
question
Ask a question
x
First name

e-mail (*)

Subject

Text (*)

(*) required fields
sendclose
Variants
Code
Description
 
15000107-08
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 8 lt. Europe I
 
15000107-10
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 10 lt. Europe I
 
15000107-12
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 12 lt. Luxury I
 
15000107-15
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 15 lt. Europe II
 
15000107-20
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 20 lt. Europe II
 
15000107-25
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 25 lt. Europe II
 
15000107-30
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 30 lt. Luxury II
 
Informations

Code:
15000107

Weight:
10 Kg

Description
Automatic water softener valve Fleck 5600 SXT 1" electronic (Reg. Metered-time) 8-10-12-15-20-25-30 lt. resin
click to enlargeclick to enlargeclick to enlargeclick to enlargeclick to enlargeclick to enlargeclick to enlarge
click on images to enlarge
Full description
FLECK 5600 SXT Electronic valve Automatic meter/time regeneration. Program with high performance which allows a low water and salt per regeneration consumption. Valve body made of Noryl plastic material, NSF listed. Programming is simple and fast, just enter time, day of week, time of regeneration, typically 02.00 at night, number of days between regenerations and hardness input. Complete with plug adapter 12/230V - 50Hz European plug. Hardness regulator output. Is raccomended a minimum hardness in output of around 15 °F , but most commonly used setting is not less than 5 ° F. Loosening setting screw will allow clapper by-pass to close. The closing action will reduce mixing with raw water output. To mix a specific output hardness value, adjust screw and test water. Repeat procedure until you reach desired hardness value. To check input/output hardness from device, we recommend to buy cod. 13000001 Titrant kit total hardness (1°F) 15cc single reagent.

TO BUY WITH EVERY SOFTENER
1x 02001014 3-pieces standard housing 10" clear IN-OUT 1" with wrench & wall mounting bracket.
2x 04001006-05 Ionicore wound polypropylene cartridge 9-3/4'' - 50 micron (50)
1x Kit 13000001 Titrant total hardness (1 ° F) 15cc single reagent.
* Water softeners are supplied without salt, we recommend to use pads salt.

The device is supplied programmed with a input hardness of 40°F, hardness of 0°F output and a safety regeneration every 7 days.The bypass valves isolate device from water system and allow the use of untreated water. Routine maintenance or service may also require that system is put in bypass.

What are the benefits that SXT Controller offer?
* Simple and intuitive programming
* Large LCD display with blue backlight
* 48 hours of internal power backup
* Real time of day in hours and minutes
* Residual volume of softened water
* Display of cycle regeneration phases and remaining time
* Service and self-diagnosis indicators
* Fast and easy capacity, time and day of regeneration configuration
* Advanced programming options, including ability to program up to 6 cycles of regeneration with independent adjustment of time
* The program setting will not be lost in case of power outages remaining in memory
* Electronic regeneration step-by-step
* Manually, delayed or immediate regeneration

Benefits and advantages
Reduction of water hardness, which is cause of scale. ENERGY SAVING: the device prevents formation of deposits in pipes and hydraulic lines. Greater sense of wellness during shower. Skin soft and clean. Increased duration of appliances and boilers. COST SAVING: reduction in use of soaps, fabric softeners and chemicals. Reduced maintenance costs. Fully automatic operation. It should just worry about adding salt in water softner.

Increased sodium (for drinking water)
Most of the sodium consumed is taken with foods, especially ones obtained with industrial processing. Salt is a great preservative and therefore is used as an additive for processed products. The assumption of sodium with the water we drink is relatively low compared to that which is taken with food. All softeners to produce softened water through ion exchange resins in, produce softened water output sodium ions. The recommended sodium limit for water intended for human consumption is 200ppm liter. Depending on sodium concentration and water hardness, it is possible that water presents an higher sodium concentration than recommended. Where this is the case or if you need to follow a low salt content, it is advisable to install a domestic reverse osmosis for drinking water.

Specifications
* Min. pressure: 1.4 bar (1.4 kg/cm2)
* Max. pressure: 8.5 bar (8.5 kg/cm2)
* Min. temperature: 2 ° C
* Max. temperature: 43 ° C
* Input/Output water 1" female thread
* Exhaust: hose connector with 2m. of tube
* Overflow: hose connection 3/8"

Model Specifications 15000107-08 8lt. resin (for 1/2 people)
* Exchange capacity: 38.56 º HFxm3.
* Salt consumption for regeneration: 0.88 Kg./Salt.
* Water consumption for regeneration: 47,2lt.
* Quantity of treated water for regeneration, 30°F-1,28m3, 35°F-1,10m3, 40°F-0,96m3, 45°F-0,85m3, 50°F-0,77m3, 60°F-0,64M3.
* Max. flow: 0.36 m3/h
* Dimensions Europe I - Base (mm): 480x320 * Height (mm): 655

Model Specifications 15000107-10 10lt. resin (for 1/2 people)
* Exchange capacity: 48,20ºHFxm3.
* Salt consumption for regeneration: 1,10 Kg./salt.
* Water consumption for regeneration: 63,8lt.
* Quantity of treated water for regeneration, 30°F-1,6m3, 35°F-1,38m3, 40°F-1,21m3, 45°F-1,07m3, 50°F-0,97m3, 60°F-0,80m3.
* Max. flow: 0,45m3/h
* Dimensions Europe I - Base (mm): 480x320 * Height (mm): 655

Model Specifications 15000107-12 12lt. resin (for 2/3 people)
* Exchange capacity: 57,84ºHFxm3.
* Salt consumption for regeneration: 1,32 Kg./salt.
* Water consumption for regeneration: 70,8lt.
* Quantity of treated water for regeneration, 30°F-1,93m3, 35°F-1,65m3, 40°F-1,44m3, 45°F-1,29m3, 50°F-1,16m3, 60°F-0,96m3.
* Max. flow: 0,54m3/h
* Dimensions Luxury I - Base (mm): 605x350 * Height (mm): 670

Model Specifications 15000107-15 15lt. resin (for 3/4 people)
* Exchange capacity: 72,30ºHFxm3.
* Salt consumption for regeneration: 1,65 Kg./salt.
* Water consumption for regeneration: 90,7lt.
* Quantity of treated water for regeneration, 30°F-2,41m3, 35°F-2,06m3, 40°F-1,80m3, 45°F-1,60m3, 50°F-1,45m3, 60°F-1,20m3.
* Max. flow: 0,67m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120

Model Specifications 15000107-20 20lt. resin (for 4/6 people)
* Exchange capacity: 96,40ºHFxm3.
* Salt consumption for regeneration: 2,2 Kg./salt.
* Water consumption for regeneration: 124,1lt.
* Quantity of treated water for regeneration, 30°F-3,21m3, 35°F-2,75m3, 40°F-2,41m3, 45°F-2,14m3, 50°F-1,93m3, 60°F-1,60m3.
* Max. flow: 0,9m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120

Model Specifications 15000107-25 25lt. resin (for 6/8 people)
* Exchange capacity: 120,50ºHFxm3.
* Salt consumption for regeneration: 2,75 Kg./salt.
* Water consumption for regeneration: 150lt.
* Quantity of treated water for regeneration, 30°F-4,01m3, 35°F-3,44m3, 40°F-3,01m3, 45°F-2,67m3, 50°F-2,41m3, 60°F-2,00m3.
* Max. flow: 1,12m3/h
* Dimensions Europe II - Base (mm): 480x320 * Height (mm): 1.120

Model Specifications 15000107-30 30lt. resin (for 6/8/10 people)
* Exchange capacity: 144,60ºHFxm3.
* Salt consumption for regeneration: 3,30 Kg./salt.
* Water consumption for regeneration: 179,7lt.
* Quantity of treated water for regeneration, 30°F-4,82m3, 35°F-4,13m3, 40°F-3,61m3, 45°F-3,21m3, 50°F-2,89m3, 60°F-2,41m3.
* Max. flow: 1,35m3/h
* Dimensions Luxury II - Base (mm): 605x350 * Height (mm): 1.120
Related products
Customers Login
e-mail
password

Everpure CLARIS Antiscale watre filters for coffe maker

www.sinergroup.it Everpure Filters